Sales

                  ---We provide complete and partial mooring setups or just about anything/combination you can imagine.
Mushroom moorings come in sizes of 50 pounds to over 1000.  The mooring you choose will depend on the size of
your boat.  
Boat size Regulation.  We also sell and service Helix moorings.  They are screwed in the sea floor bed and
have a tremendous amount of holding power.  We suggest the helix mooring if you have a larger boat (25 feet or
greater).  There are significant environmental and cost savings over time.  Please contact us for more information.  
508-648-5839
1)Mushroom Anchor  ---(Barnstable County Requirements)
SALTWATER
Boat Size -Mooring Weight- Bottom & Top Chain- Pennant
  • 00-13' 50 lbs 1/2" 3/8" 1/2"
  • 14-17' 75 lbs 1/2" 3/8" 5/8"
  • 18-21' 150 lbs 1/2" 3/8" 5/8"
  • 22-25' 200 lbs 5/8" 1/2" 5/8"
  • 26-31' 250 lbs 5/8" 1/2" 3/4"
  • 32-35' 300 lbs plus sw 5/8" 1/2" 3/4"
  • 36-40' 500 lbs plus sw 3/4" 1/2" 3/4"
  • Over 40' Harbormaster Approval

FRESHWATER
Boat Size -Mooring Weight -Bottom & Top Chain -Pennant
  • 00-17' 50 lbs 1/2" 3/8" 1/2"
  • 18-21' 100 lbs 1/2" 3/8" 5/8"
  • 22-25' 150 lbs 5/8" 1/2" 5/8"
  • 26’ over Harbormaster Approval


2)
Helix Anchor
The following specifications shall be considered the minimum allowable specifications of a helix mooring system.
(1) The shaft must be a minimum of 1 1/2” thick and at least six feet in length.
(2) The shaft and helix must be of galvanized or other non-corrosive metal, such as stainless steel.
(3) The shaft must be designed to allow the bottom chain to swivel around the shaft and to be replaced when
necessary.
(4) There shall be a minimum of 2 helixes attached to each shaft with the lower helix being a minimum of 8” in diameter
and the top helix being a minimum of 10” on diameter.
(5) All chain and pennant specifications will remain consistent with the mushroom anchor chart.
(6) Installation of helix moorings must be done by a Mooring Servicer.
(7) It shall be the responsibility of the Mooring Servicer to assure that the proper size and length helix is used
according to subsoils within a given mooring area and for the vessel to be moored.
(8) The mooring servicer shall record the position of the helix mooring by a GPS fix and record all the mooring
specifications including the length of shaft, depth of mean high water, torque reading at set, all sizes and length of
ground tackle. All information shall be filed with the Harbormasters Office within 10 days of work.
(9) All helix moorings shall be installed as close to flush with the bottom surface as possible with no more than 6”
protruding above the bottom surface.
    Prices

                                               Mushroom Moorings  all United States Steel!

                 50 lbs. --- $70.00            150 lbs. --- $187.50        300 lbs. --- $375.00
                 75 lbs. --- $
95.00            200 lbs. --- $250.00        350 lbs. --- $440.00
                 100 lbs. --$1
30.00          250 lbs. ---  $312.50       400 lbs. --- $500.00
                                                         500 lbs.----$
625.00        $1.25/lb. 600-1000lbs.

                                               Ballast Balls(shaft weights) 80lbs.-- $120.00

                                                      
Pyramid Anchors--U.S. made

                  50 lbs. --- $75.00            150 lbs. --- $217.50           300 lbs. --- $435.00
                
  75 lbs. --- $112.50          200 lbs. --- $290.00           350 lbs. --- $510.00
                 100 lbs. --$1
50.00           250 lbs. ---  $362.50          400 lbs. --- $580.00
                                                         500 lbs.----
 $725.00         $1.45/lb 600-1000lbs.


                                         
Anchor Chain Hot Dipped Galvanized 43 Proof

               3/8 inch  --- $4/foot     1/2 --- $5.50/foot      5/8 --- $8.50/foot     3/4 --- $11.50/foot    1"--$15/foot

                                                                 
Shackles
                                                                                                                          
               3/8 inch --- $4.5    1/2 --  $8.50     5/8 -- $12   3/4 -- $16   1" -- $27  1 1/4" -- $38


                                                                 
Swivels

               3/8 inch ---$9.00   1/2  --  $12.50    5/8 --  $18   3/4 --  $24   1" --  $32


                                                    
Mooring Balls --TC3(Taylor)

               12"  --- $82          15" --  $105    18" -- $135     24" --  $205     30" --  $375